Specifically designed for use at site surveys, it´s small, compact design and battery capacity allow for many hours of continuous use. It is the ultimate site survey tool and a must have for all Wi-Fi engineers! Great for performing wireless site surveys, portable IP camera set up´s, temporary wireless bridge connections, and charging mobile phones and tablets. Multiple PoE outputs Lightweight and portable Charge while in use LCD display toggles between battery percentage and voltage Operating voltage: 110-220V Battery input (2.1mm): 12.6V DC, 2A Battery output (2.1mm): 12V, 2A PoE Output: IEEE 802.af, 802.3at & 802.3bt (Type 3 & 4) complaint USB 2.0 Output: 5V DC, 2A USB C Output: Up to 20V, 5A Battery Type & Capacity: Lithium-Ionnen 7500 mAh 12.6V/94.5 Wh Dimensions 5.5" H x 3.9" W x 1.875" D (140 mm x 100 mm x 48 mm) Operating temperature: 14-140F (-10 to 60 C) Colour: Black Included in delivery: 1x Accelerator Battery Pack Version 2 1x one portable carrying bag 1x one wall charger 1x 2.1 mm plug-plug connection for the 12V output Available downloads:Download The Accelerator Site Survey Battery Pack V2 Data Sheet

Portable POE Installation Tool with Rechargeable Battery POINTSOURCE Plus is ideal for powering POE IP cameras in-situ, when in-line POE is not yet available. It permits complete camera alignment, focus, configuration and test from a locally-connected laptop. Portable, Rechargeable, Power Where You Need It Veracity’s POINTSOURCE Plus is a portable, rechargeable battery - powered POE (Power over Ethernet) injector. It is designed for field use, being compact, easy to handle, with a useful shoulder strap, which leaves your hands free. It can deliver enough power to support a full day’s IP camera installation work. POINTSOURCE Plus provides a similar functionality to Veracity’s PINPOINT, but includes a built-in POE power source to allow installation and set-up of IP cameras before POE power is available through the network. On Site Configuration The most common application for POINTSOURCE Plus is the in-situ configuration, set-up and fine adjustment of IP cameras on an installation site. By simply connecting a laptop to the IP camera through POINTSOURCE Plus, all aspects of the camera image (focus, direction, aperture, zoom, resolution, compression etc.) can easily be viewed and adjusted. On Site Surveys and Pre-Installation Trials POINTSOURCE Plus allows the rapid set-up of an IP camera during site surveys, allowing the integrator to capture snapshots or video clips of the actual on-site scenes for presentation to the prospective end-user. This is an effective example of the saying "A picture paints a thousand words.” Customer Demonstrations Can Be Given Anywhere Any new IP camera can very quickly be demonstrated to a client or consultant using just the camera, a laptop and the POINTSOURCE Plus package. No external power or network switch is required, allowing demonstrations to be done anywhere, from a café table top to a desert road. Mobile & Temporary Installations A POINTSOURCE Plus and IP camera with an SD-card slot are all that is required for a very compact and easily transported temporary IP video surveillance recording system. POE and POE Plus POINTSOURCE Plus complies with universal IEEE 802.3af and IEEE 802.3at POE standards, and can deliver up to 25 watts of POE power. Integrated network crossover ports allow the direct connection of a laptop (shown in the diagram opposite). USB Charging Point A convenient 5V USB port is provided for charging smart phones and tablets, whilst on site. The USB port has no data connection function. LED Indicator The POE port LED indicates when POE is being delivered to a compatible device connected to the Camera port. If an incompatible device is connected (or needs too much power) then the red LED will flash indicating the problem. Removable Battery Module POINTSOURCE Plus has a removable, rechargeable battery module which provides enough power for a full day’s installation work. The battery module is removed for recharging purposes. Additional battery modules are also available as an option. Battery Life and Status POINTSOURCE Plus has a battery life of 3 to 5 years, or 200 - 1000 cycles depending upon discharge depth and operating temperature. The battery status indicator shows the remaining charge in steps of 25%. The simple design of the system allows the removable battery to be recharged whilst POINTSOURCE Plus continues to be used with a second battery. PoE Output: 48V DC, IEEE802.3af and 802.3at compliant (PoE and PoE Plus) USB Output: 5V DC, 2.1A, power only, no data Battery type: Maintenance-free, sealed lead-acid battery 12V, 3.4Ah Battery modul: Removable, rechargeable battery module Discharge life: 6 hours continuous for a 5 watt camera (typical) Charger: Three-stage intelligent (14.4V / 1A / 13.8V float) Camera Port: 10/100BaseTX with PoE Network Port: 10/100BaseTX with data only (laptop connection) PoE Status indicator: Red LED shows ON, flash indicates error, off indicates no PoE Battery status indicator: Green four-bar display indicates charge level: 100% - 75% - 50% - 25% Network port LEDs: Green: Link speed  / Orange: Network activity Network connectors: 2x RJ45, one with PoE USB connector: 1x USB Typ A (power only) Charging connector: 2.1mm jack, centre positive (on battery module - remove unit to charge) Weight: approx. 2.2 Kilo Dimensions: Lenght 205 mm x Wide 100 mm x Hight 150 mm Operation temperature: 0C to 50CAvailable downloads: Download POINTSOURCE PLUS Datasheet Download POINTSOURCE PLUS Quickstart Guide

The Power over Ethernet (PoE) Tester, connected to an RJ-45 outlet, tests the cabling infrastructure for the presence of power, either IEEE802.3af or IEEE802.3 at standard compliant. The PoE Tester identifies the existence and type of Power Sourcing Equipment (either Endspan or Midspan) in your network. Features Tests RJ-45 outlet for Power over Ethernet existence Works over Cat5 or better cable Detects: IEEE 802.3af midspans and switches Cisco pre-standard in-line switches High Power midspans Power over 2 pairs or 4 pairs Compact design specifically tailored for system integrators and installers Plug and play for ease of use System Description A PoE system comprises a PSE (Power Sourcing Equipment) and a PD (Powered Device). The PSE may either be an Endspan (i.e. a layer 2 Ethernet Switch with integrated PoE) or a Midspan, while the PD is a PoE-enabled terminal, such as IP phone, Wireless LAN access point and Network Security Camera. The PoE tester will check your RJ-45 outlet for power and identify its source, Midspan or Endspan, i.e.IEEE 802.3af, 802.3at or UPoE/EEPoE standard compliant Midspans/Switches. How to use the PoE Tester: Connect a standard category 5 or better cable with RJ-45 connectors to the PoE tester and the RJ-45 outlet (See diagram). Check the LED indicators on the front panel for power and source (PoE switch,Midspan or High Power Midspan). The lit-pattern of LEDs will identify amount of power, and whether it is over 2 or 4 pairs. .. (this should match the colors in the picture of the midspan green LED/OFF LED – 802.3af standard level PoE powering- over spare pairs (PoE source = midspan) green LED/OFF LED – 802.3af standard level PoE powering- over spare pairs (PoE source = midspan) OFF LED/Green LED – 802.3af standard level PoE powering – over data pairs (PoE sourc = Switch) Blue LED / OFF LED – 802.3at standard level PoE powering – over spare pairs (PoE source = Midspan) OFF LED / Blue LED – 802.3at standard level PoE powering – over data pairs (PoE source = Switch) Green LED / Green LED – 802.3af standard level PoE powering, using all 4 pairs Blue LED / Blue LED – 802.3at standard level PoE powering, using all 4 pairs – 60WAvailable downloads: Download Microsemi PoE Tester Datasheet

The Microsemi PowerDsine´s PD-AS-951 High Power active splitter enables data terminals that were not originally designed to accept power from the Ethernet, to be powered by Power over Ethernet midspans. The PD-AS-951 High power splitter (user selectable 12V or 24V) can power devices such as WiMax CPE´s, small WiMAX base-stations, 802.11n Access Points, Thin- Clients, PTZ (Pan/Tilt/Zoom) IP Cameras, Video Phones and more. Many contemporary terminals are designed and deployed without the ability to accept power via their LAN input. Such devices can only accept power through ther DC jack while their RJ45 input accept only data. Moreover, such devices might only accept voltage levels lower than the PoE standard minium voltage (44v in IEEE802.3af / 50v in 802.3at). Using the PD-AS-951 high power splitter, these terminals immediately become PoE-ready without any modification required on their side. The splitter is identified as a powered device (PD) in front of the powering Midspan and after being detected and powered, it physically splits the data and power streams, arriving over a single cable, into two seperate cords (LAN & DC) which go directly to the data terminal. Voltage regulation is also performed to the level required by the termin (12V or 24V.)Available downloads: Download Microsemi High Power Splitter PD AS 951 Datasheet