Air suspended tripod with 16 mm head with 1/4" and 3/8" thread. The safe, fixed design is both lightweight and portable, making it ideal for site surverys. The telescopic folding mechansim minimizes the dimensions of the tripod when folded and allows quick folding and unfolding. The height adjustment is infinitely adjustable thanks to the profile locks and the bolt. The non-slip feet stabilize the tripod with precision. The tripod is additionally air suspended. The lowering of the Access Point mounted on the tripod is therefore gentle and slow and the risk of damage is much lower than with spring loaded tripods. Robust and durable materials - Metal tripod (screw holder, T-piece and hook are made of plastic) Height adjustable from approx. 120 to 320 cm height 16 mm double sided studio head (1/4 and 3/8 inch thread) Air suspended telescopic unfolding mechansim Clamps that block the sections - wing screws non slip feet max. load capacity 3 - 10 Kilo (10 Kilo for min. height, 3 Kilo for max. height)

This aluminium high tripod is manufactured by a family owned factory in Germany. With an extended length of 10.50 meter and a load capacity of up to 8 kilos, the aluminium high tripod is perfect for WiFi Site Surveys in logistic warehouses, various types of factories and distribution centres. Due ot the inserted length of 1.90 meter and a transport weight of approx. 28 kilos, this aluminium high tripod is very easy to transport.  The aluminium high stand consists of an aluminium round mast to which four feet are attached. The individual feet are telescopic so that small unevennesses in the terrain can be compensated. The round masts consist of several aluminium tubes that are inserted into each other and polished on one side and pushed out by hand. The sturdy clamps securely lock the extended tubes in place.    The maximum permissble extension lenght is limited by a marking ring. There is no fixed stop when pulling out. There are two markings for safety. When the first mark is reached, the telescopic tube should then be slowly pushed out to the second mark and locked in place by the clamp when this is reached.  The aluminium high tripod and the round mast are made of anodised aluminium round tubes (AlMgSi05 F22) with a 2 mm wall thickness. The own weight is approx. 28 kilos and is therefore very low.  ** Note: When using the aluminium high tripod with a head load, bracing must be carried out depending on the existing wind conditions.**   Aluminium high tripod, black anodised 10.50 metres extended height Inserted length: 1.90 metres Extended length: 10.50 metres Colour: black anodised Tube diameter (mm): 70/65/60/55/50/45/40 Material: Aluminium Load capacity: up to 8 Kilo Transport weight: approx. 28 Kilo  Head: 1/4" photo thread (removable) Country of origin: Germany

Bag for tripod with shoulder strap 80 cm length Inside length: approx. 80 cm Inside width: 6-7 x -6-7 cm Colour: Black belt lenght: up to 85 cm

Counterweight - sandbag for tripods Dimensions: 23 x 50 cm Maximum total weight of sand: 8 Kilo (4 Kilo per bag) Sand is not included !

The Klein Tools VDV Scout Pro 3 is a portable voice-data-video cable tester. It tests and troubleshoots RJ11, RJ12, RJ45 and F-connector terminated cables and provides tone generation or cable tracing. The VDV Scout Pro 3 also measures cable length, tests for shield, performs hub uplink testing and traces up to 19 locations (up to 5 locations with the included remotes, additional remotes are available separately).   WARNINGS: To ensure the safe operation and service of the tester, please follow these instructions. Failure to observe these warnings can result in severe injury or death. The PoE Jack, located on the right side of the Scout Pro 3 is the only jack designed for poE energised cables. Connecting AC energised cables to any port may damage it and pose a safety hazard to the user. Improperly terminated RJ plugs have the potential to damage the jacks on the VDV Scout Pro 3. Visually inspect an RJ plug before inserting it into the tester. The contacts should always be recessed into the plastic housing of the plug. Plugging 6-positions plugs into the 8-position jack on the tester has the potential to damage the outer-most contacts of the jack, unless the plug is specifically designed for that purpose.   Specifications: Dimensions: 16,5 x 7,6 x 4,1 cm Battery Life (9V alkaline):- Standby: 4 years- Active: 50 hours (without backlight) Weight: 312 gr with battery and remote Operating temperature: 0° bis 50 °C Storage temperature: -20°C to 60 °C Humidity: 10% to 90%, non-condensing Maximum Voltage (between any two connector pins without damage):- RJ Jack: 66V DC or 55V AC- F-Connector: 66V DC or 55V AC Cable types: Shielded or unshielded; CAT7A, CAT7, CAT6A, CAT6, CAT5E, CAT3, Coaxial Lenght Measurement Method: Capacitance Length Measurement Range: 1.5 to 1999' (0.5m to 610m) with 15 pF/ft Length Accuracy: (5% ft) or (5% m) Length Constant Range: 10 pF/ft to 40 pF/ft (33 pF/m to 132 pF/m) RJ45 Port: Data cable, Ethernet cable, CAT5E, CAT6, CAT6A, CAT7, CAT7A F-Connector Port: Video cable, coaxial cable, RG6/RG6Q cable, RG59 cable RJ11/12 Port: Voice cable, POTS (plain old televoice service) cable, 4-wired cable, 6-wire cable, 2 twisted-pair cables, 3 twisted-pair cables, CAT3 Available downloads: Download Datenblatt VDV501853 (DE) Download Data Sheet VDV501853 (ENG)

The Microsemi PowerDsine´s PD-AS-951 High Power active splitter enables data terminals that were not originally designed to accept power from the Ethernet, to be powered by Power over Ethernet midspans. The PD-AS-951 High power splitter (user selectable 12V or 24V) can power devices such as WiMax CPE´s, small WiMAX base-stations, 802.11n Access Points, Thin- Clients, PTZ (Pan/Tilt/Zoom) IP Cameras, Video Phones and more. Many contemporary terminals are designed and deployed without the ability to accept power via their LAN input. Such devices can only accept power through ther DC jack while their RJ45 input accept only data. Moreover, such devices might only accept voltage levels lower than the PoE standard minium voltage (44v in IEEE802.3af / 50v in 802.3at). Using the PD-AS-951 high power splitter, these terminals immediately become PoE-ready without any modification required on their side. The splitter is identified as a powered device (PD) in front of the powering Midspan and after being detected and powered, it physically splits the data and power streams, arriving over a single cable, into two seperate cords (LAN & DC) which go directly to the data terminal. Voltage regulation is also performed to the level required by the termin (12V or 24V.)Available downloads: Download Microsemi High Power Splitter PD AS 951 Datasheet

The Power over Ethernet (PoE) Tester, connected to an RJ-45 outlet, tests the cabling infrastructure for the presence of power, either IEEE802.3af or IEEE802.3 at standard compliant. The PoE Tester identifies the existence and type of Power Sourcing Equipment (either Endspan or Midspan) in your network. Features Tests RJ-45 outlet for Power over Ethernet existence Works over Cat5 or better cable Detects: IEEE 802.3af midspans and switches Cisco pre-standard in-line switches High Power midspans Power over 2 pairs or 4 pairs Compact design specifically tailored for system integrators and installers Plug and play for ease of use System Description A PoE system comprises a PSE (Power Sourcing Equipment) and a PD (Powered Device). The PSE may either be an Endspan (i.e. a layer 2 Ethernet Switch with integrated PoE) or a Midspan, while the PD is a PoE-enabled terminal, such as IP phone, Wireless LAN access point and Network Security Camera. The PoE tester will check your RJ-45 outlet for power and identify its source, Midspan or Endspan, i.e.IEEE 802.3af, 802.3at or UPoE/EEPoE standard compliant Midspans/Switches. How to use the PoE Tester: Connect a standard category 5 or better cable with RJ-45 connectors to the PoE tester and the RJ-45 outlet (See diagram). Check the LED indicators on the front panel for power and source (PoE switch,Midspan or High Power Midspan). The lit-pattern of LEDs will identify amount of power, and whether it is over 2 or 4 pairs. .. (this should match the colors in the picture of the midspan green LED/OFF LED – 802.3af standard level PoE powering- over spare pairs (PoE source = midspan) green LED/OFF LED – 802.3af standard level PoE powering- over spare pairs (PoE source = midspan) OFF LED/Green LED – 802.3af standard level PoE powering – over data pairs (PoE sourc = Switch) Blue LED / OFF LED – 802.3at standard level PoE powering – over spare pairs (PoE source = Midspan) OFF LED / Blue LED – 802.3at standard level PoE powering – over data pairs (PoE source = Switch) Green LED / Green LED – 802.3af standard level PoE powering, using all 4 pairs Blue LED / Blue LED – 802.3at standard level PoE powering, using all 4 pairs – 60WAvailable downloads: Download Datasheet

Specifically designed for use at site surveys, it´s small, compact design and battery capacity allow for many hours of continuous use. It is the ultimate site survey tool and a must have for all Wi-Fi engineers! Great for performing wireless site surveys, portable IP camera set up´s, temporary wireless bridge connections, and charging mobile phones and tablets. Multiple PoE outputs Lightweight and portable Charge while in use LCD display toggles between battery percentage and voltage Operating voltage: 110-220V Battery input (2.1mm): 12.6V DC, 2A Battery output (2.1mm): 12V, 2A PoE Output: IEEE 802.af, 802.3at & 802.3bt (Type 3 & 4) complaint USB 2.0 Output: 5V DC, 2A USB C Output: Up to 20V, 5A Battery Type & Capacity: Lithium-Ionnen 7500 mAh 12.6V/94.5 Wh Dimensions 5.5" H x 3.9" W x 1.875" D (140 mm x 100 mm x 48 mm) Operating temperature: 14-140F (-10 to 60 C) Colour: Black Included in delivery: 1x Accelerator Battery Pack Version 2 1x one portable carrying bag 1x one wall charger 1x 2.1 mm plug-plug connection for the 12V output Available downloads: download datasheet

The WiFi Stand Rail allows you to quickly and easily mount a wireless access point on a standard T-Rail, even when there is no drop ceiling! Attach it to a 1/4" 20 threaded screw and slide your access point on! Made of the same industrial strength PVC, machined aluminum connection points, and quality that the WiFi Stand Bracket is made out of, this ultra-light and easily transportable rail can go with you wherever you need it! Please note: Mounting hardware is not included with purchase.

When deploying, testing, or temporarily placing wireless Access Points, sometimes you need creative placement to mimic coverage or geht into a tight space. The WiFi Stand vertical Bracket is here to help, giving you a way to mount an Access Point at a 90-degreee angle. Built with input from the WiFi users community, our vertical Bracket is made of the same solid, durable, and lightweight Industrial grade PVC and milled aluminium. An added touch to this bracket is the raised edge along the rail to keep your Access Points from sliding all the way off! Built around the standard 1/4-20 mount to attach universally to tripods and stands, as well as the 24mm drop-ceiling T-rail for the widest product support, our WiFi Stand brackets have already received international recognition throughout the industry. Now, we once again take user input into consideration and present our vertical bracket! Please note: Stand is not included with purchase, this is for the bracket only. Each bracket attaches to a universal 1/4-20 threaded screw found on most tripods and stands. Please see our store for recommended stands to attach bracket to.